Enmet EN Series Manual de usuario descargar pdf (Pagina 7)

Sensor/Transmitter, Toxic Gas & Oxygen ENMET Corporation

4.0

Standard Ranges, Calibration Gases, Voltage Readings at Calibration Points and

Approximate Times to Sensor Stabilization

Table 1: Electrochemical Sensors

Gas

Symbol

Range*

(ppm)

Calibration Gas

Correlation

Reading

(mV)

Stabilize

(min.)

ENMET Gas

Part Number

Ammonia NH

0 – 100 25ppm NH

200 4 03218-025

Arsine (2) AsH

0 – 0.5 0.5ppm PH

0.375ppmAsH

400 3 03202-005

Boron Trichloride BCl

0 – 30 10ppm HCl 10ppm BCl

233 3 03202-010

Carbon Monoxide CO 0 – 100 50ppm CO 300 2 03219-050

Chlorine (2) Cl

0 – 10 5ppm Cl

300 4 03231-005

Chlorine Dioxide ClO

0 – 1.0 0.3ppm ClO

** 220 4 **

Dichlorosilane SiH

0 – 30 10ppm HCl 3ppm SiH

140 3 03202-010

Ethylene Oxide C

O 0 – 30 5ppm C

O 167 3 03232-005

Fluorine (2) F

0 – 10 3ppm Cl

7.5ppm F

400 3 03231-003

Hydrogen H

0 – 1000 800ppm H

420 3 03227-800

Hydrogen Bromide HBr 0 – 30 5ppm HCl 25ppm HBr 433 3 03202-005

Hydrogen Chloride (2) HCl 0 – 30 10ppm HCl 233 3 03202-010

Hydrogen Cyanide HCN 0 – 30 10ppm HCN 233 2 03203-010

Hydrogen Fluoride (1) HF 0 – 10 5ppm Cl

3ppm HF 220 4 03202-005

Hydrogen Sulfide H

S 0 – 100 20ppm H

S 180 2 03214-020

Nitrogen Dioxide NO

0 – 30 5ppm NO

167 2 03233-005

Nitric Oxide NO 0 – 100 25ppm NO 200 1.5 03234-025

Oxygen O

0 – 30 % 20.9% O

379 2 03296-209

Ozone (1) O

0 – 1.0 0.3ppm O

** 220 3 **

Phosgene (1) COCl

0 – 1.0

0.66ppm COCl

364 4 **

Phosphine (2) PH

0 – 1.0 0.5ppm PH

300 1.5 03205-005

Silane SiH

0 – 30 5 ppm SiH

167 2 03306-005

Silicon Tetrachloride SiCl

0 – 30 5ppm HCl 25ppm SiCl

433 3 03202-005

Sulfur Dioxide SO

0 – 30 10ppm SO

233 1.5 03215-010

OTE

: All specifications stated in this manual may change without notice.

(1) Require use of Sample Draw System.

(2) Recommended use of Sample Draw System, for enhanced sensitivity and speed of response.

*0 = 4mA = 100mV, upper point = 20mA = 500 mV

**Gas not available in cylinders, a gas generator must be used

OTE

: If a non-standard range and/or a non-standard calibration gas are used, utilize the equations in Section 3.0 to determine

voltage readings.

1 2 3 4 5 6 7 8 9 10 11 12 ... 18 19

Comentarios a estos manuales

Sin comentarios

Enmet EN Series Manual de usuario Pagina 7

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Enmet EN Series