Enmet EX-6100 Series Manual de usuario descargar pdf (Pagina 19)

EX-6100

ENMET Corporation

11 Menu Mode

The EX-6100 uses a password system to restrict the end user from carrying out certain changes that may compromise the use of the

equipment. Menu Mode should only be entered by qualified personal.

To enter the menu mode Sequence Tap:

Menu, Up, Down, Enter, Up, Enter, Up, Menu

If no inputs (taps) the EX-6100 returns to operational mode.

Several calibration modes exist in the EX-6100 and these are accessible via the instruments simple menu system. To select a calibration

mode follow this procedure:

• Press the MENU button, E: 1 appears on the display.

• Press UP or DOWN until the required menu option is displayed.

• Press ENTER to select the calibration mode.

• To exit the menu press MENU.

While the instrument is in menu mode – any data displayed on the screen will alternate between the cal number and the reading.

The following features are available via the ‘EX-6100’ menu system:

Table 3: EX-6100 Menu Options

Menu Option Section

E : 1 – Sensor Zero 11.2.1

E : 2 – Sensor Span 11.2.2

E : 3 – Sensor FSD 11.2.3

E : 4 – Output Zero (4mA) 11.2.4

E : 5 – Output Span (20mA) 11.2.5

E : 6 – Decimal Places 11.2.6

E : 7 – Firmware Version 11.2.7

E : 8 – Restore 11.2.8

E : 9 – Engineer Diagnostics 11.2.9

 E : 12 – Cross Reference 11.2.10

E : 13 – Relay 1 11.2.11

E : 14 – Relay 2 11.2.12

E : 15 – Alarm Level 1 11.2.13

E : 16 – Alarm Level 2 11.2.14

E : 19 – Positive Zero Suppression 11.2.15

E : 20 – Negative Zero Suppression 11.2.16

E : 27 – Hysteresis 11.2.17

 E : 28 – Firmware Update 11.2.18

E : 29 – Relay 3 11.2.19

E : 30 – Password 11.2.20

E : 31 – Warm-Up Timer 11.2.21

 Contact ENMET Corporation before entering this menu option.

 Do Not enter this menu option.

11.2.1 E : 1 – Sensor Zero

Refer to section 5.1.1 for sensor calibration details.

11.2.2 E : 2 – Sensor Span

Refer to section 5.1.2 for sensor calibration details.

11.2.3 E : 3 – Sensor FSD

This menu option allows the full-scale gas level to be selected.

From the menu system select menu option: E: 3 and press ENTER.

• Using the INCREASE and DECREASE buttons; adjust the FSD to the required level.

• Press ENTER, ‘- - - - ‘will be displayed to indicate that the new setting has been accepted.

Note: Pressing MENU instead of ENTER will exit the menu without changing the FSD.

• Press MENU to close the menu system.

11.2.4 E : 4 – Output Zero (4mA)

Refer to section Appendix A for output calibration details.

11.2.5 E : 5 – Output Span (20mA)

Refer to section Appendix A for output calibration details.

1 2 ... 14 15 16 17 18 19 20 21 22 23 24 ... 27 28

Comentarios a estos manuales

Sin comentarios

Enmet EX-6100 Series Manual de usuario Pagina 19

Comentarios a estos manuales

Relacionado con productos y manuales para Instrumentos de medición Enmet EX-6100 Series